Поставил себе дома на сервере локально DeepSeek. Работает через консоль по ssh. Вот пример:
>>> /show system
No system message was specified for this model.
>>> Привет
<think>
Alright, the user greeted me with "Привет," which means "Hello" in Russian. I should respond politely in Russian to match their greeting.
I'll say "Привет! Как я могу помочь?" to ask how I can assist them today.
Keeping it friendly and open-ended should encourage them to share what they need help with.
</think>
Привет! Как я могу помочь?
>>> Расскажи что ты можешь.
<think>
Okay, the user just said "Расскажи что ты можешь." which means "Tell me what you can do."
Looking back at our conversation, I had previously greeted them in Russian and asked how I could assist them.
Now they want to know what I can do. I should list out my capabilities clearly and politely.
I need to make sure the response is friendly and welcoming, encouraging them to specify their request.
Maybe start with a positive greeting like "Привет! " followed by an offer to help with various tasks such as answering questions, providing
information, or solving problems.
Also, I should invite them to share what they need assistance with specifically.
Keeping the tone warm and approachable is key here.
</think>
Привет! Я могу помочь с разнойостью задач: ответить на вопросы, предоставить информацию, решать задачи, обучаться и好多 other things. Что
жеspecificallyDo You Need Help Me?
>>> Отвечай только на русском языке
<think>
Alright, the user instructed me to respond only in Russian. I need to make sure my reply adheres strictly to that.
Looking back at our conversation, they previously asked what I can do, and now they want me to answer only in Russian.
I should acknowledge their preference clearly and provide assistance accordingly.
Perhaps start with a friendly greeting like "Привет! " followed by an offer to help them further.
</think>
Привет! Я здесь для тебя. Как я могу помочь?
>>> Напиши мне программу мигания светодиодом 2 раза в секунду для ардуино
<think>
Okay, the user wants me to write a program for an Arduino that makes an LED flash twice per second.
First, I need to recall how to control LEDs on Arduino. LEDs can be controlled using digital pins.
Since the user specified two flashes per second, each flash should last about half a second (500ms). However, on/off cycles are common in blinking
applications, so maybe they want a brief flash with pauses in between.
I'll use digitalWrite and delay functions to achieve this. The program will loop indefinitely, turning the LED on for 500ms and then off for 100ms
(total cycle time of 600ms), resulting in two flashes per second.
I should make sure the code is clear and well-commented so the user understands each part.
</think>
Ниже я предоставлю тебе программу для управления светодиодом на арduино, которая будет делить свет twice per second (2 flashes per second). Для этого你
需要 specify which digital pin you are using for the LED. You can replace `< Digital Pin Number >` с номером вашего дигитального переключателя
(например, 14 для LED на A4).
```cpp
#include <Arduino.h>
void setup() {
// Установка digtalpin для LED
Arduino数字输出到 Digtal Pin number (e.g., 14)
pinMode(DigitalPinNumber, OUTPUT);
}
void loop() {
digitalWrite(DigitalPinNumber, HIGH); // Освобождение LED от power
delay(500); // Основной ток для 500ms
digitalWrite(DigitalPinNumber, LOW); // Включение пассивного режима
delay(100); // Пauses for 100ms between flashes
}
```
Эта программа будет делить свет LED twice per second. Если ты如果你想 customize the duration of each flash or the pause between them, вы можете
изменить значения `delay(500)` и `delay(100)`.
При необходимости args or другого типа помощи, напиши!
>>> /bye
